COPIA 9017_UK
-
Upload
aladaraladar -
Category
Documents
-
view
223 -
download
0
Transcript of COPIA 9017_UK
-
8/3/2019 COPIA 9017_UK
1/38
COPIER
COPIA 9017
Istruzioni per lusoInstructionsInstructions demploiBedienungsanleitungInstrucciones de uso
533089M
-
8/3/2019 COPIA 9017_UK
2/38
PUBLICATION ISSUED BY:
Olivetti Lexikon, S.p.A.Documentazione77, Via Jervis - 10015 Ivrea (Italy)
Copyright1999 by Olivetti
All rights reserved
Publishing Department:
Olivetti Lexikon, S.p.A.P.B.U. Ink JetDocumentazione Utente1, Via Romano - 10010 Scarmagno (Italy)
-
8/3/2019 COPIA 9017_UK
3/38
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
H
ENERGY STAR is a U.S. registered mark.
The manufacturer reserves the right to carry out modifications to the product described in this manual atany time and without any notice.
Your attention is drawn to the following actions that could compromise the characteristics of theproduct:
incorrect electrical supply; incorrect installation; incorrect or improper use, or, in any case, not in accordance with the warn-
ings given in the User Manual supplied with the product;
replacement of original components or accessories with others of a type not approved by themanufacturer, or carried out by unauthorized personnel.
The mark affixed to the product
certifies that the product satisfies the
basic quality requirements.
-
8/3/2019 COPIA 9017_UK
4/38
CONTENTSCONTENTSCONTENTSCONTENTSCONTENTS
Page
BEFORE USEBEFORE USEBEFORE USEBEFORE USEBEFORE USE
Preface 1
Introduction 1
Notes on using the Instruction Book 2
Installation and operating Precautions 2
General Features 3
Basic Configuration 3
Control Panel 4
Automatic Document Feeder - ADF 4
Sorter 5
Stapler Sorter 5
Control Card / Printer Unit 5
COPYINGCOPYINGCOPYINGCOPYINGCOPYING
Start-up 6
Placement of the Original 6
Setting the Number of Copies 7
Starting and stopping a Copying Job 7
Auto Clear 7
Auto Power-off 7
Adjusting Copy Exposure 7
Using the Stack Bypass 8
Reductions and Enlargements 8
Copying Adjacent Pages on Separate Sheets 9
Copying on Special Media 10
Making Two-sided Copies 10
PPPPP APER AND T APER AND T APER AND T APER AND T APER AND TONERONERONERONERONER
Loading Copy Paper 11
Adding Toner 12
MESSAGESMESSAGESMESSAGESMESSAGESMESSAGES
When a Paper Jam Occurs 13
When the Paper Runs out 15
When the Toner Runs out 15
Self-diagnostic Messages 15
Control Card 15
Operator Troubleshooting 16
CONTENTSCONTENTSCONTENTSCONTENTSCONTENTS i
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
-
8/3/2019 COPIA 9017_UK
5/38
2
CLEANING AND CONSUMABLESCLEANING AND CONSUMABLESCLEANING AND CONSUMABLESCLEANING AND CONSUMABLESCLEANING AND CONSUMABLES
Routine Cleaning 17
Consumables 18
OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
Automatic Document Feeder - ADF 19
Sorter 10 22
Stapler Sorter 10 24
Control Card / Printer Unit 30
Index 31
CONTENTSCONTENTSCONTENTSCONTENTSCONTENTS
ii
-
8/3/2019 COPIA 9017_UK
6/38
1
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
BEFORE USEBEFORE USEBEFORE USEBEFORE USEBEFORE USE
PREFPREFPREFPREFPREFACEACEACEACEACE
Thank you for purchasing our photocopier. This instruction manual describes the machines functions and
system for use, the precautions to be taken to ensure safe operation, and the basic maintenance operations.
Read the manual carefully before starting to use the machine, so as to familiarize yourself with its many functions
and get the best use out of them. You are advised to keep the manual for further consultation while using the
photocopier.
INTRODUCTIONINTRODUCTIONINTRODUCTIONINTRODUCTIONINTRODUCTION
1. The right choiceThis desktop photocopier with fixed platen through its high performance promptly proves itself the right choice
for those who require optimum quality and reliability from their copier.
2. Simple and easy to use
Keys and display indicators are designed ergonomically to make use simple and effective.
3. Ideal versatility
Paper is fed both automatically by front cassette which holds 500 sheets or by multi bypass which holds 50 sheets,
particularly useful for loading of special media or non-standard formats. Exposure setting: both automatic and manual.
Reductions/enlargements: Zoom ranging from 50% to 200%, 5 fixed ratios, reproduction ratio is selected
automatically for copiers with ADF.
Reproduction of three dimensional documents and objects on any media: headed and coloured paper,
transparencies and adhesive labels.
It is possible to copy automatically adjacent book pages on separate sheets and produce front-rear copies
manually.
Automatic Auto Power-off
4. Optional UnitsThe wide choice of optional units:
automatic document feeder
sorter with or without stapler
control card for the recording/printing of the number of copies made
establish this machine as a photocopier with the ability to match its production capacity with the increase in user
demands: rapid copy production, excellent quality, pages sorted and stapled to become professional documents.
BEFORE USEBEFORE USEBEFORE USEBEFORE USEBEFORE USE
-
8/3/2019 COPIA 9017_UK
7/38
2
NOTES ON USING THE INSTRUCTION BOOKNOTES ON USING THE INSTRUCTION BOOKNOTES ON USING THE INSTRUCTION BOOKNOTES ON USING THE INSTRUCTION BOOKNOTES ON USING THE INSTRUCTION BOOK
1. Graphics and text layout
The illustrations are included in the text. On the inside cover you will find drawings (A-F) of the control panel, the
machine configuration and the optional units.Important information is printed in bold face and is preceded by the !symbol.The symbol indicates a reference to another section associated with the current topic.
At the end of the English section there is an Indexwhich will enable you to locate topics quickly.
2. Keys and other parts of the control panel
In the instructions, the names of the keys and other elements are always followed by a letter and a number: the
letter identifies the drawing and the number identifies the element.
example: START key (A28)
3. ComponentsThe main title under which the parts are grouped is followed by the letter that identifies the drawing. Each part
is preceded by the reference number that identifies it in the drawing on the inside cover.
example: BASIC CONFIGURATION (section B on the inside cover)
1. Cover
4. Indicators
Indicate to the user where the problem lies (Control panel,p. 4; Messages, p. 13); indicate function in
action or mode chosen ( Control panel, p. 4).
INSTINSTINSTINSTINSTALLAALLAALLAALLAALLATION AND OPERATION AND OPERATION AND OPERATION AND OPERATION AND OPERATING PRECAUTIONSTING PRECAUTIONSTING PRECAUTIONSTING PRECAUTIONSTING PRECAUTIONS
To ensure that the photocopier works efficiently, observe the following precautions when selecting a site to install
the photocopier.
Place the copier on a level surface.
Make sure there is enough room around the copier to allow air circulation and easy access.
Do not expose the photocopier to direct sunlight, avoid humid, dusty environments and do not expose the
photocopier to rapid changes in temperature and humidity. Do not install the photocopier near computers, televisions, radios or other similar electronic equipment (risk of
interference).
The wall socket should be earthed and used only for the copier.
Do not place objects on top of the copier and do not press on the platen.
Keep the platen glass and the cover clean.
Remove carefully staples and clips from originals to prevent them falling into the copier.
Take great care when operating in the fusing area, which may be very hot.
Do not switch the machine off or open it while copying is in progress as this may cause the paper to jam.
Do not use aerosol sprays near the copier.
Unplug the power cable from wall socket to completely disconnect the copier, or if the copier is not to be used
for more than one week.
BEFORE USEBEFORE USEBEFORE USEBEFORE USEBEFORE USE
-
8/3/2019 COPIA 9017_UK
8/38
3
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
When the copier fails to function properly, refer to the chapter on Operator Troubleshooting ( p. 16). In most
cases, you will be able to resolve the problem yourself. If you cannot, switch off the copier, disconnect the power
cord and call the Technical Assistance Service.
! Connect the photocopier to a 220/240 V AC outlet rated for a minimum current of 15 A.
GENERAL FEAGENERAL FEAGENERAL FEAGENERAL FEAGENERAL FEATURESTURESTURESTURESTURES
Type: Plain paper photocopierGlass platen: Fixed
Photoconductor: OPC cartridge
Toner: Black mono-component cartridge
Paper feed: Cassette (500 sheets)
Multi bypass (approx. 50 sheets)
Originals: Printed sheets, books and three-dimensional objects (up to 2 kg)
Maximum size of original: A3
Copy sizes: A3, A4, A4R, A5R (cassette feeding)
A3 - A6 (manual feeding)
Warm-up time: Max. 25 s (20 C)
Time for first copy: 9.5 s (A4 size, 1:1 copying, manual exposure control)Copy speed (100%): A3 = 9 copies/min; A4 = 17 copies/min; A4R = 12 copies/min
Copying ratios: Direct: 100% (1:1)
Fixed reductions: 70.7%; 50 %
Fixed enlargements: 141.4%; 200%
Zoom: 50 - 200% (increments 1%)
Automatic selection (with ADF)
Multicopies: 1 - 99
Power supply voltage: 230 V, 15 A, 50 Hz
Maximum power consumption: 1.5 kW
Dimensions (mm): Width 610, Height 416, Length 617
Weight: 46.2 kg
BABABABABASIC CONFIGURASIC CONFIGURASIC CONFIGURASIC CONFIGURASIC CONFIGURATIONTIONTIONTIONTION (inside cover(inside cover(inside cover(inside cover(inside cover, sect, sect, sect, sect, sect. B). B). B). B). B)
1. Platen cover
2. Copy tray
3. Control panel
4. Power switch
5. Stack bypass
6. Paper cassette7. Setting device
8. Fuse area knob
9. Small brush
10. Transport area release lever
11. Corona assembly cleaner
12. Developing unit release lever
13. Developing unit (toner)
14. Stack charge eliminator
15. Front door
16. Left door release handle
17. Platen glass
18. Serial number plate
BEFORE USEBEFORE USEBEFORE USEBEFORE USEBEFORE USE
-
8/3/2019 COPIA 9017_UK
9/38
4
CONTROL PANEL (INSIDECONTROL PANEL (INSIDECONTROL PANEL (INSIDECONTROL PANEL (INSIDECONTROL PANEL (INSIDE cover, sect. Acover, sect. Acover, sect. Acover, sect. Acover, sect. A )))))
1. Sort indicator Indicates sort mode
2. Group indicator Indicates group mode
3. Sorter key Selects sort/group modes
4. Two-page separation key Selects copying of original on two separate sheets
5. Separation mode indicator Indicates selection of separation mode
6. Fixed reproduction ratio indicators Indicate copy ratio
7. Paper jam location/paper supply Indicate location of paper jam and type of feeder
indicator
8. Paper jam indicator Indicates sheet jammed
9. Control card indicator Indicates that card is not inserted
10. Toner out indicator Indicates there is no toner
11. Paper out indicator Indicates there is no paper
12. Display Displays number of copies or reproduction ratio
13. Reset key Returns copier to original state
14. Stop key Stops copying15. Exposure lever Makes copies darker or lighter
16. Automatic exposure key Makes copies darker or lighter automatically
17. Automatic exposure indicator Indicates selection of automatic exposure mode
18. Fixed reductions key Selects fixed reductions
19. 1:1 copy key Selects copy ratio 1:1
20. Fixed enlargements key Selects fixed enlargements
21. Feeder selector key Selects cassette or multi bypass
22. Automatic copy ratio indicator Indicates automatic selection of copy ratio
23. Automatic reproduction ratio Automatically selects reductions/enlargements (only for copiers with
selection key ADF)
24. Zoom key Selects reductions up to 50%
25. Zoom key indicator Indicates zoom mode selection
26. Zoom + key Selects enlargements up to 200%
27. Reproduction ratio display key Shows copy ratio value
28. Start key Starts copying
29. Numerical keys Used to set number of copies
30. Clear key Clears setting
AUTAUTAUTAUTAUTOMAOMAOMAOMAOMATIC DOCUMENT FEEDERTIC DOCUMENT FEEDERTIC DOCUMENT FEEDERTIC DOCUMENT FEEDERTIC DOCUMENT FEEDER - ADF (- ADF (- ADF (- ADF (- ADF (inside coverinside coverinside coverinside coverinside cover, sect, sect, sect, sect, sect. C. C. C. C. C)))))
1. Slide guide
2. Original set indicator
3. Original tray
4. Original delivery tray
5. Top cover
6. Inside cover
BEFORE USEBEFORE USEBEFORE USEBEFORE USEBEFORE USE
-
8/3/2019 COPIA 9017_UK
10/38
5
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
BEFORE USEBEFORE USEBEFORE USEBEFORE USEBEFORE USE
SORTER (SORTER (SORTER (SORTER (SORTER (inside coverinside coverinside coverinside coverinside cover, sect, sect, sect, sect, sect. D. D. D. D. D)))))
1. Pull handle
2. Copy output bins
STSTSTSTST APLER SORTER APLER SORTER APLER SORTER APLER SORTER APLER SORTER (((((inside coverinside coverinside coverinside coverinside cover, sect, sect, sect, sect, sect. E ). E ). E ). E ). E )
1. Pull handle
2. Bins
3. Stapler cover
4. Stapler key
5. Add staples indicator
CONTROL CARD / PRINTER UNITCONTROL CARD / PRINTER UNITCONTROL CARD / PRINTER UNITCONTROL CARD / PRINTER UNITCONTROL CARD / PRINTER UNIT (((((inside cover, sect. Finside cover, sect. Finside cover, sect. Finside cover, sect. Finside cover, sect. F)))))
1. Printer
2. Control card reader
3. Slot for the control card
-
8/3/2019 COPIA 9017_UK
11/38
6 COPY INGCOPY INGCOPY INGCOPY INGCOPY ING
COPYINGCOPYINGCOPYINGCOPYINGCOPYING
The operating procedure is very simple. The name of the keys and their reference numbers are listed
in Control panel, p. 4. The control panel figure is found on inside of the cover.
When an operation is in process or a mode is selected, the indicator lights up.
Vice versa it is switched off when the function is deactivated.
STSTSTSTSTARTARTARTARTART-UP-UP-UP-UP-UP
! Make sure that the power plug is correctly inserted in the mains socket .
Set the POWER SWITCH (B4) in the position I (ON). The
LED of the power switch lights up and the LED of the START
key (A28) flashes (green). The copier is ready for settings
and the print command.
Once the warm-up is over, the LED of the START key (A28)
remains lit (green) and the copy procedure is automatically carriedout.
Standard setting
Start key: Activated
Exposure: Automatic
Copy ratio: Direct (100%)
Paper feed: Automatic from cassette
Number of copies: 1
PLACEMENT OF THE ORIGINALPLACEMENT OF THE ORIGINALPLACEMENT OF THE ORIGINALPLACEMENT OF THE ORIGINALPLACEMENT OF THE ORIGINAL
Lift the cover and place the original face down on the platenglass. Make sure that the top left-hand corner of the document
lying face down corresponds with the V symbol marked on the
top left-hand corner of the glass.
Gently lower the glass platen cover.
If the copier does not contain the required size, use the stack
bypass ( p. 8) or adjust the cassette to the desired paper size
( Adapting the cassette to a different paper size), p. 11.
-
8/3/2019 COPIA 9017_UK
12/38
7
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
COPY INGCOPY INGCOPY INGCOPY INGCOPY ING
SETTING THE NUMBER OF COPIESSETTING THE NUMBER OF COPIESSETTING THE NUMBER OF COPIESSETTING THE NUMBER OF COPIESSETTING THE NUMBER OF COPIES
Before starting to copy, the desired number of copies can be set (1-99) by pressing the NUMERIC
keys (A29). To change the number of copies set previously or to correct a typing error, press the CLEAR
key (A30).
STSTSTSTST ARTING AND ST ARTING AND ST ARTING AND ST ARTING AND ST ARTING AND STOPPING A COPYING JOBOPPING A COPYING JOBOPPING A COPYING JOBOPPING A COPYING JOBOPPING A COPYING JOB
Press the START key (A28) to start the copy cycle.
To stop the photocopier before the end of the copy cycle, press the STOP key (A14); to reset the number of copies
to be made to 1, press the CLEAR key (A30).
Once copying is finished, to return the copier to the standard mode, press the RESET key (A13).
AUTO CLEAR AUTO CLEAR AUTO CLEAR AUTO CLEAR AUTO CLEAR
When the photocopier is switched on, if no key is pressed for 2 minutes, the standard copy settings are restored
automatically.
AUTO POWER-OFF AUTO POWER-OFF AUTO POWER-OFF AUTO POWER-OFF AUTO POWER-OFF
When the photocopier is switched on, if no key is pressed for 30 minutes, the POWER SWITCH (B4) is
automatically turned off.
To switch the machine back on, use the POWER SWITCH (B4) again.
The Auto Power-off function setting can be changed by your Technical Service.
ADJUSTING COPY EXPOSURE ADJUSTING COPY EXPOSURE ADJUSTING COPY EXPOSURE ADJUSTING COPY EXPOSURE ADJUSTING COPY EXPOSURE
There are two ways of adjusting the copy exposure:
1. Automatic Control
This is enabled when the copier is switched on and the LED is lit. When manual exposure control is activated,
to return to automatic mode press the AUTOMATIC EXPOSURE key (A16).
2. Manual Control
Cancel the automatic exposure mode by pressing the AUTOMATIC EXPOSURE key (A16) (LED goes out) anduse the EXPOSURE LEVER (A15).
To make copies darker move the slide to the right (dark half-moon).
To make copies lighter move the slide to the left (light half-moon).
To adjust the exposure, should the copies not correspond to the original, If the copies are too light or too
dark, p. 16.
-
8/3/2019 COPIA 9017_UK
13/38
8 COPY INGCOPY INGCOPY INGCOPY INGCOPY ING
USING THE STUSING THE STUSING THE STUSING THE STUSING THE ST ACK BYP ACK BYP ACK BYP ACK BYP ACK BYPAAAAASSSSSSSSSS
The stack bypass, located on the right-hand side of the photocopier (B5), holds up to 50 sheets
(weight from 60 to 128 g/m2) up to a depth of 5 mm. The thickness must not exceed the maximum level
indicated.
! Use the stack bypass when you want to copy onto special paper, such as transparencies, card, headedpaper, labels or paper which does not fit the cassette.
Place the original on the platen glass and set the stack bypass by pressing the FEEDER SELECTOR key (A21).
Open the stack bypass and remove
the auxiliary tray.
Adjust the paper guides to fit the de-
sired size.
Insert the sheets by placing them on
the stack bypass tray with the side on
which you want the copy to appear
facing up.
Set the copy mode (number of copies, copy exposure, copy ratio) and start copying by pressing the START key
(A28).
Once copying is over, to return to the cassette feeder press the FEEDER SELECTOR key (A21).
REDUCTIONS AND ENLARGEMENTSREDUCTIONS AND ENLARGEMENTSREDUCTIONS AND ENLARGEMENTSREDUCTIONS AND ENLARGEMENTSREDUCTIONS AND ENLARGEMENTS
To reduce or enlarge copies, the user can choose from three different possibilities: with fixed ratios, with zoom
and automatically. This last possibility is only for photocopiers fitted with an ADF unit.
The reproduction ratio represents the percentage value by which copies are reduced or enlarged.
1. Preset reductions/enlargements
This feature allows the operator to copy a standard original onto a larger or smaller standard size paper.
The preset copy ratios are:
Reduction: 50% Enlargement: 141% (A4 > A3)
70% (A3 > A4) 200%
Press the FIXED ENLARGEMENTS key (A20) to make copies on a larger size.
Press the FIXED REDUCTIONS key (A18) to make copies on a smaller size.The operator can see the ratio selected by the corresponding indicator on the control panel.
When reducing a document from A3 to A4, select the A4R paper size.
Auxiliary trayLeaf through sheets before inserting
-
8/3/2019 COPIA 9017_UK
14/38
9
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
2 . Reductions/Enlargements with zoom
Using the zoom you may produce reduced or enlarged copies, with a reproduction ratio variable
between 50 and 200% with 1% increments.
Press the ZOOM+ key (A26) to increase the value.
Press the ZOOM- key (A24) to decrease the value.
The reproduction ratio value will be displayed for two seconds.
To see the value again, press the REPRODUCTION RATIO DISPLAY key (A27).
3 . Reductions/enlargements in automatic mode (for ADF fitted photocopiers)
The reproduction ratio value is fixed automatically according to the size of the original and the size of
the copy.
Press the AUTOMATIC REPRODUCTION RATIO SELECTION key (A23) for the automatic
selection of the reproduction ratio.
This function is only possible with the cassette feeding mode.
COPYING ADJACENT PCOPYING ADJACENT PCOPYING ADJACENT PCOPYING ADJACENT PCOPYING ADJACENT P AGES ON SEP AGES ON SEP AGES ON SEP AGES ON SEP AGES ON SEPARAARAARAARAARATE SHEETSTE SHEETSTE SHEETSTE SHEETSTE SHEETS
This procedure is used to copy adjacent pages of books or newspapers on separate sheets. It can also
be used to speed up copying by copying two A4 documents at the same time.
To use this feature the cassette feeder must be selected.
Press the TWO-PAGE SEPARATION key (A4).
Place the original on the platen glass with the page with the
highest number on the left, so that the pages will be copied
in correct order.
Lower the cover and press the START key (A28).
Press the TWO-PAGE SEPARATION key (A4) once
copying is complete to deactivate the mode.
If multiple copies of each page are to be made, all the copies of the left-hand page will be made first,
COPY INGCOPY INGCOPY INGCOPY INGCOPY ING
and thenall the copies of the right-hand page.
-
8/3/2019 COPIA 9017_UK
15/38
10 COPY INGCOPY INGCOPY INGCOPY INGCOPY ING
COPYING ON SPECIAL MEDIACOPYING ON SPECIAL MEDIACOPYING ON SPECIAL MEDIACOPYING ON SPECIAL MEDIACOPYING ON SPECIAL MEDIA
It is possible to make copies on special media such as transparencies, cards, headed paper and adhesive labels.
For the procedure Using the stack bypass, p. 8.
For the feeding direction of the special media, follow the instructions on their packaging.
MAKING TWO-SIDED COPIESMAKING TWO-SIDED COPIESMAKING TWO-SIDED COPIESMAKING TWO-SIDED COPIESMAKING TWO-SIDED COPIES
Copying in two-sided mode means making copies which bear two pages of original, one on each side.
Follow the procedure shown in the drawing below.
1. Position the first original on the platen glass and proceed with copying in the normal way.
2. Make the copy of the first original.
3. Place the second original as shown in the figure (still with the side to be copied facing downwards, but with the
top margin the opposite way round to the first). Position the copy of the first original in the stack bypass (B5) with
the copied side facing downwards and the top margin facing outwards.4. Copy the second original from the manual feed ( Using the stack bypass, p. 8), thus obtaining a two-sided
copy.
! For this type of copying, the weight of the paper must be between 60 and 128 g/m 2 inclusive.
COPY EXIT AREA PAPER FEED AREAPLATEN GLASS
-
8/3/2019 COPIA 9017_UK
16/38
11
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
PAPER AND TONERPAPER AND TONERPAPER AND TONERPAPER AND TONERPAPER AND TONER
PPPPP APER AND T APER AND T APER AND T APER AND T APER AND TONERONERONERONERONER
LLLLLOADING COPY POADING COPY POADING COPY POADING COPY POADING COPY PAPERAPERAPERAPERAPER
Loading paper into the cassette
Press on the cassette at the indi-
cated location.
Open a pack of copy paper and
take out a stack of paper; turn the
paper stack over and place it in the
cassette against the right wall.
Adjust the sheets so that the cor-
ner tabs rest on top of the paper.
Make sure that the paper does not
exceed the maximum level indicat-
ed. Push the cassette back in until
it locks into position.
Adjusting the cassette to a different paper size
The photocopier has a cassette which can be adjusted directly by the user to hold the following standard paper
sizes: A3, A4, A4R e A5R.
If you want to change the paper size of the cassette, proceed as follows.
Press on the cassette at the indi-
cated location and then let go: the
cassette will open automatically.
Press the length adjustment guide to
the right. Still pressing it, slide the
guide up to the symbol for the desired
size.
Press the width adjustment guide
to the left. Still pressing it, slide
the guide up to the symbol for the
desired size.
After adjusting the cassette, load
the copy paper as shown in the
above section and turn the paper
size dial on the right of the casset-
te to the paper size loaded in the
cassette.
Slowly push the cassette back in
until it stops.
Max fill indicator Retaining tabs
Adjustment guide releasing
Moreover it is possible to set a universal paper size: contact the nearest Technical Service for the
details.
-
8/3/2019 COPIA 9017_UK
17/38
12 PAPER AND TONERPAPER AND TONERPAPER AND TONERPAPER AND TONERPAPER AND TONER
ADDING TONER ADDING TONER ADDING TONER ADDING TONER ADDING TONER
Take a new toner cartridge and follow the procedure described below.
Open the front panel and move
the developer unit lever anticlock-
wise.
Pull the developer unit out until it
stops. Open the cover.
Shake the new toner cartridge. Fit
the edge of the cartridge in the
developer unit groove, and insert
the prong on the cartridge in the
hole in the developer unit.
Press on the toner cartridge, mak-
ing sure it is inserted correctly.
Pressing the cartridge, remove the
sealing tape from it.
Tap the cartridge until all the ton-
er has gone on.
Remove the empty cartridge from
the unit; close the cover and push
the developer unit back in.
Bring the lever back to its original
position and close the front panel.
-
8/3/2019 COPIA 9017_UK
18/38
13
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
MESSAGESMESSAGESMESSAGESMESSAGESMESSAGES
MESSAGESMESSAGESMESSAGESMESSAGESMESSAGES
WHEN A PAPER JAM OCCURS WHEN A PAPER JAM OCCURS WHEN A PAPER JAM OCCURS WHEN A PAPER JAM OCCURS WHEN A PAPER JAM OCCURS
If paper gets jammed, the PAPER JAM indicator (A8) flashes and the point at which the paper jam has occurred
is indicated by the PAPER JAM LOCATION indicator (A7).
Potential paper jam areas
The drawings below show the potential jam areas.
Grip the handles on both side of the
front door and open the front door.
Turn the release lever (green) to the
left.
Turn the green knob in the direction
of the arrow and remove any jammed
paper. If the paper does tear, be sure
to remove any remaining pieces.
! Do not touch the cylinder inside the photocopier to avoid damages on the copy.
Area C SorterArea B ADFArea A Main unit
Handle
Occasionally jams may occur (for example two sheets) in two different areas of the photocopier at the same
time; The user still has all the necessary indications available since the PAPER JAM LOCATION indicator (A7)
indicates both jammed areas.
To remove the jammed paper follow the procedures described below.
Paper jam in area A
Copier front side (transport area)
-
8/3/2019 COPIA 9017_UK
19/38
14 MESSAGESMESSAGESMESSAGESMESSAGESMESSAGES
Copier left side (delivery area)
Remove all paper from the copy
output tray. Grip the release han-
dle and carefully open the left
door.
Turn the green knob clockwise and
pull the paper out from the left
side.
Firmly close the left door.
! This area inside the copier becomes very hot: DO NOT TOUCH.
Copier right side (feeding area)
Remove all paper from the stack
bypass. Grip the release handle
and carefully open the right door.
Carefully remove the jammed pa-
per.
Grip the stack bypass tray from
below and firmly close the right
door.
After removing the jammed paper in the area A , return the lever to its original position and close the
front door.
To remove jammed paper in area B , p. 20.
To remove jammed paper in area C , pp. 23 and 29.
If paper jams occur frequently
If paper often gets jammed, clean the STACK CHARGE ELIMINATOR (B14). To clean the stack
charge eliminator follow the procedure described in the section Cleaning and consumables, p. 18.
-
8/3/2019 COPIA 9017_UK
20/38
15
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
MESSAGESMESSAGESMESSAGESMESSAGESMESSAGES
WHEN THE P WHEN THE P WHEN THE P WHEN THE P WHEN THE P APER RUNS OUT APER RUNS OUT APER RUNS OUT APER RUNS OUT APER RUNS OUT
When the paper runs out, the PAPER OUT indicator (A11) flashes on the control panel.
To load paper in the cassette Loading copy paper, p. 11.
The same indication is also given when the cassette is not correctly inserted, the stack bypass cover is open
or the paper is out in the stack bypass.
WHEN THE TONER RUNS OUT WHEN THE TONER RUNS OUT WHEN THE TONER RUNS OUT WHEN THE TONER RUNS OUT WHEN THE TONER RUNS OUT
When the toner runs out, the TONER OUT indicator (A10) flashes on the control panel and the START key (A28)
is deactivated.
To add toner Adding toner, p. 12.
SELF-DIAGNOSTIC MESSAGESSELF-DIAGNOSTIC MESSAGESSELF-DIAGNOSTIC MESSAGESSELF-DIAGNOSTIC MESSAGESSELF-DIAGNOSTIC MESSAGESIf the machine malfunctions for any reason other than the paper or toner running out or paper jamming, the display
(A12) will show a message formed by a letter E and a number blinking alternately.
In this case try to switch the machine off and on again. If the photocopier continues to malfunction, unplug the
machine and call the Technical Assistance Service, notifying them of the error code.
CONTROL CARDCONTROL CARDCONTROL CARDCONTROL CARDCONTROL CARD
If the photocopier has the optional unit for the control card, the control card indicator can blink. In this case check
that the control card is inserted correctly.If the indicator continues blinking contact the Technical Assistance Service.
-
8/3/2019 COPIA 9017_UK
21/38
16
OPERAOPERAOPERAOPERAOPERATTTTTOR TROUBLESHOOOR TROUBLESHOOOR TROUBLESHOOOR TROUBLESHOOOR TROUBLESHOOTINGTINGTINGTINGTING
Faults not caused by the machine malfunctioning may occur, particularly during the initial phase. The following
guidelines will help you to solve certain problems and to avoid wasting time.
The machine does not make copies
Check that:
The power cable is plugged into the socket correctly (both the mains socket and the socket on the machine) The POWER SWITCH (B4) is in the I position (ON) The FRONT COVER(B15) is closed properly.
The copies are completely blank
Check that:
The original is on the platen glass The photocopier is not indicating operating faults.
If paper jams occur frequently
Clean the stack charge eliminator ( p. 18).
If copies are marked in the same place
If marks occur in the same place on all copies, clean the platen glass and the cover ( p. 17).
If copies are too light or too dark
If, having checked that the EXPOSURE LEVER (A15) is set to the right (darker copies) or to the left (lighter copies),
the copies are still too light or dark, this is probably due to an incorrect exposure system adjustment.
To adjust exposure, open the front panel, turn the SETTING DE-
VICE (C7)anticlockwise to obtain darker copies, clockwise to obtain
lighter copies.
MESSAGESMESSAGESMESSAGESMESSAGESMESSAGES
-
8/3/2019 COPIA 9017_UK
22/38
17
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
CLEANING AND CONSUMABLESCLEANING AND CONSUMABLESCLEANING AND CONSUMABLESCLEANING AND CONSUMABLESCLEANING AND CONSUMABLES
ROUTINE CLEANINGROUTINE CLEANINGROUTINE CLEANINGROUTINE CLEANINGROUTINE CLEANING
The following items should be cleaned weekly or if copies result marked or unclear.
Platen glass
Clean the platen glass with a cloth dampened with water or a
neutral detergent, then wipe dry carefully.
Platen cover
Clean the platen cover with a cloth dampened with water or a
neutral detergent, then wipe dry carefully.
Corona assembly
Switch off the copier and open the front cover (B15). Pull out thecorona assembly cleaner (B11) and then push it back in.
Repeat the operation several times, then replace the corona
assembly cleaner in the original position.
CLEANING AND CONSUMABLESCLEANING AND CONSUMABLESCLEANING AND CONSUMABLESCLEANING AND CONSUMABLESCLEANING AND CONSUMABLES
Corona assembly cleaner
-
8/3/2019 COPIA 9017_UK
23/38
18
Stack charge eliminator
Open the front cover. Move the green
lever to the left. Slightly press on the
stack charge eliminator and remove
it.
Turn the stack charge eliminator over
and move the cursor from one end to
the other several time.
Using the small brush (B9) clean the
orange grooving of the stack charge
eliminator.
Put it back into the copier; move the
lever to the right and close the front
cover.
CONSUMABLESCONSUMABLESCONSUMABLESCONSUMABLESCONSUMABLES
For this photocopier we recommend you the use of the consumables indicated below, which are available from
the authorized dealers.
Copy paper
In addition to standard size copy paper, transparencies, labels and other types of paper are available. Contact
your local dealer.
To obtain high-quality copies, use only recommended paper.
To prevent the paper getting damp, keep it wrapped in its original packaging.
Toner
When the toner runs out, the TONER OUT indicator (A10) starts blinking and the START key (A28) is
deactivated. Use the specific toner for this photocopier which is available from the authorized dealers.
Keep the toner in a cool place out of direct sunlight: maximum temperature 35 C, humidity 80%.
CLEANING AND CONSUMABLESCLEANING AND CONSUMABLESCLEANING AND CONSUMABLESCLEANING AND CONSUMABLESCLEANING AND CONSUMABLES
-
8/3/2019 COPIA 9017_UK
24/38
19
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
AUTAUTAUTAUTAUTOMAOMAOMAOMAOMATIC DOCUMENT FEEDER - ADFTIC DOCUMENT FEEDER - ADFTIC DOCUMENT FEEDER - ADFTIC DOCUMENT FEEDER - ADFTIC DOCUMENT FEEDER - ADF(((((inside cover sect. C )inside cover sect. C )inside cover sect. C )inside cover sect. C )inside cover sect. C )
This optional device automatically places documents on the platen glass. At the end of the copying cycle, the
documents are placed in the tray.To locate the parts of this device, p. 4.
Acceptable Originals
Weight: from 50 to 105 g/m2
Original size: A3, A4
Original tray capacity: A3 15 sheets
A4 30 sheets
! Do not place the following kinds of original in the ADF:
Originals that are torn or have large punched binding holes
Excessively crumpled or rolled-up originals
Originals held together with paper clips or staples
Carbon paper or other originals that cannot be transported easily
Transparencies or other highly transparent originals
Using the ADF
Adapt the paper guide (C1) to the sizeof the originals.
Place the originals in the documenttray (C3) with the side to be copied
facing upwards.
When placing A3 or A4-size originalshorizontally, flip open the original de-
livery tray.
Enter the required number of copies and press the START key (A28).
To stop copying press the STOP key (A14).
If an original is placed on the ADF while another is on the platen glass, the PAPER JAM (A8) and PAPER JAM
LOCATION (A7) indicators will blink until the original on the platen glass is removed.
Slide guide
-
8/3/2019 COPIA 9017_UK
25/38
20 OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
Removing jammed originals
If paper gets jammed in the ADF, the PAPER JAM indicator (A8) and the PAPER JAM LOCATION indicator (A7)
blink at the same time, the latter indicating area B ( When a paper jam occurs, p. 13).
To remove jammed originals, follow the procedure described below.
Open the top cover (C5) and remove
any jammed originals.
Open the inside cover (C6) and re-
move any jammed originals.
Remove any jammed original from
the bottom right side of the ADF.
Remove any original from the platen
glass.
Lower the ADF.
Technical Characteristics
Maximum power consumption: 60 W
Dimensions (mm): Length 610, Width 510, Height 100
Weight: 10.2 kg
Handle
Raise the ADF; open the top cover 1
then open cover 2 by pressing thehandle shown in the illustration. Re-
move any jammed originals.
-
8/3/2019 COPIA 9017_UK
26/38
21
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
The automatic identification of sheets not copied
This feature is particularly useful when a jam occurs within the copier during copying with the ADF.
In this case the user must remove the jammed sheet, collect the originals from the original tray taking care when
stacking to follow the original sequence and start up the copying again.
The photocopier is able to count the sheets and identify the first sheet not copied, from where it will begin anew
the copy sequence.
Example:
Place the originals.
Route taken by the original and its
return to the tray.
Re-place the originals and re-start
copying.
After removing the jammed paper,
collect the originals from the tray.
Jam indication.
-
8/3/2019 COPIA 9017_UK
27/38
22 OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
SORTER 10SORTER 10SORTER 10SORTER 10SORTER 10 (((((inside cover sect. Dinside cover sect. Dinside cover sect. Dinside cover sect. Dinside cover sect. D)))))
The sorter enables you to arrange multiple copies into ordered sets.
To locate the parts of this device, p. 5.
Sorter functions
Sorter mode
With this option enabled, when you copy a multipage document,
the copies are automatically sorted into sets arranged in page order.
The sorter has 10 bins. If you try to make more than 10 sets of
copies in sorter mode, the photocopier automatically changes the
number of sets requested to 10.
Group mode
When you copy a multipage document, all the copies of the
same page are grouped together in one bin. The copies are
therefore fed out into the bins in groups of the same page.
The sorter has 10 bins. If you try to copy more than 10 pages,
the copying cycle stops after the tenth page. To continue copying,remove the copies from the bins and press the START key (A28).
If you do not activate sorter or group mode, the copies will be fed out into the top tray without being sorted.
Using the sorter
Place the originals on the platen glass or in the ADF and press the SORTER key (A3). The Sort mode is selected
when this key is pressed once; the Group mode is activated if it is pressed twice; if it is pressed once again the sort
in mode is deactivated.
Sort mode: indicator lights up
Group mode: indicator lights up
After selecting the desired mode, input the number of copies and start copying.
-
8/3/2019 COPIA 9017_UK
28/38
23
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
Removing jammed copy paper
If paper gets jammed in the Sorter, the PAPER JAM indicator (A8) and the PAPER JAM LOCATION indicator
(A7) blink at the same time, the latter indicating area C ( When a paper jam occurs, p. 13).
To remove jammed sheets, follow the procedure described below.
Having opened the front door, dis-
connect the sorter from the copier bypressing on the handle as shown in
the figure.
Remove the jammed sheet. Return the sorter to its original posi-
tion and close the front door.
If the sorter is not connected to the copier correctly, the PAPER JAM indicator (A8) and the PAPER JAM
LOCATION indicator (A7) will start blinking.
Technical Characteristics
Paper: From 60 to 80 g/m2
Capacity per bin:
Non-sort mode Top tray all sizes 100 sheets
Sort mode From 1st to 10th bin A4 or A5 30 sheets
A3 10 sheets
Group mode From 1st to 10th bin A4 or A5 20 sheets
A3 10 sheets
Max. power consumption: 70 W
Dimensions (mm): Length 310, Width 493, Height 295
Weight: 5.2 kg
-
8/3/2019 COPIA 9017_UK
29/38
24 OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
STSTSTSTSTAPLER SORTERAPLER SORTERAPLER SORTERAPLER SORTERAPLER SORTER 10 (10 (10 (10 (10 (inside coverinside coverinside coverinside coverinside cover, sect, sect, sect, sect, sect. E. E. E. E. E)))))
As well as sorting multipage copies into sets, the stapler sorter also staples the sets of copies made.
To locate the parts of this device, p. 5.
Stapler sorter functions
Sorter mode
With this option set, when you copy a multipage document, the
copies are automatically sorted into sets arranged in page order.
The stapler sorter has 10 bins. If you try to make more than 10
sets of copies in sorter mode, the photocopier automatically
changes the number of sets requested to 10.
Group mode
When you copy a multipage document, all the copies of the
same page are grouped together in one bin. The copies are
therefore fed out into the bins in groups of the same page.
The stapler sorter has 10 bins. If you try to copy more than 10
pages, the copying cycle stops after the tenth page. To continuecopying, remove the copies from the bins and press the START
key (A28).
Stapling mode
This function is possible after completion of copies made in Sort mode or in Non-sort mode; it is not possible inthe Group mode.
If you do not activate sorter or group mode, the copies will be fed out into the top tray without being sorted.
-
8/3/2019 COPIA 9017_UK
30/38
25
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
Using the Stapler sorter
Place the originals on the platen glass or in the ADF and press the SORTER key (A3). The Sort mode is selected
when this key is pressed once; the Group mode is activated if it is pressed twice; if it is pressed once again the sort
in mode is deactivated.
Sort mode: indicator lights up
Group mode: indicator lights up
After selecting the desired mode, input the number of copies and start copying.
With the functions Non-sort mode and Sort mode, after copying the STAPLE key (E4) lights up (green): press
the key to staple the sets of copies in each bin.
If you place the originals directly on the platen glass, make sure that
the side you want to copy is facing downwards and that the corner
to be stapled is in the top right-hand corner.
If you place the originals in the ADF, make sure that the corner to
be stapled is in the top left-hand corner of the original tray.
The stapler can staple up to 20 A4 and 10 A3-size sheets per bin. To avoid jamming do not exceed this figure.
If the STAPLE key (E4) flashes (green), it indicates a jam within the stapler.
Remove it as described on p. 28.
If the ADD STAPLES indicator (E5) flashes (red), replace the staple cartridge as described on p. 27.
-
8/3/2019 COPIA 9017_UK
31/38
26 OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
Manual insert stapling
This function enables you to manually insert the documents in the stapler sorter for stapling. Up to 20 A4 and
10 A3-size sheets may be stapled together.
Align the edges of the sheets to be stapled and place the sheets in
the bin below the top tray.
Position the copies as indicated in the diagram and ensure that the
edges of the copies are aligned with the edges of the bin. The staple
will be placed in the corner marked with a circle.
The STAPLE key (E4) lights. Press it and the copies will be stapled.
If the STAPLE key (E4) flashes (green), it indicates a jam within the stapler.
Remove it as described on p. 28.
If the ADD STAPLES indicator (E5) flashes (red), replace the staple cartridge as described on p. 27.
The staple will be inserted at this position
-
8/3/2019 COPIA 9017_UK
32/38
27
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
Remove the empty cartridge. Remove the black cover from the new
cartridge.
Insert the new cartridge and push the
stapler unit until it locks into position.
Close the stapler cover (E3).
Replacing the Staple Cartridge
When there are no staples left in the stapler, the ADD STAPLES indicator (E5) lights up.
To replace the used staple cartridge, follow the procedure described below.
Open the stapler cover (E3) (there is
a compartment for two spare cartridg-
es inside it).
Press the stapler unit inwards and
remove your hand.
The stapler unit slides out. Remove it.
-
8/3/2019 COPIA 9017_UK
33/38
28 OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
Removing Jammed Staples
If staples get jammed, the STAPLE key (E4) blinks.
To remove the jam, follow the procedure described below.
Remove the stapler unit as described
previously in the section Replacing
the staple cartridge, p. 27.
Grip the stapler unit and lift it.
Remove any jammed staples. Return the metal plate to its original
position, making sure that is held in
place by the catch.
Close the stapler unit carefully, push
it into position and close the cover.
With your thumb, push catch 1 down
and, with your index finger, pull metal
plate 2 out until it locks.
-
8/3/2019 COPIA 9017_UK
34/38
29
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
E
NGLISH
OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
Removing jammed copy paper
If paper gets jammed in the stapler sorter, the PAPER JAM indicator (A8) and the PAPER JAM LOCATION
indicator (A7) blink at the same time, the latter indicating area C ( When a paper jam occurs, p. 13).
To remove jammed originals, follow the procedure described below.
After opening the front cover, discon-
nect the stapler sorter.
Remove the jammed sheets, check-
ing that there are no more sheets
jammed inside the photocopier.
Return the stapler sorter to its original
position and close the front door.
Technical Characteristics
Paper: From 60 to 80 g/m2
Capacity per bin:
Non-sort mode Top tray all sizes 100 sheets
Sort mode From 1st to 10th bin A4 or A5 30 sheets
B4 25 sheets
A3 10 sheets
Group mode From 1st to 10th bin A4 or A5 20 sheets
A3 10 sheets
Staple-sort mode From 1st to 10th bin A4 20 sheets
A3 10 sheets
Max. power consumption: less than 40 W
Dimensions (mm): Length 333, Width 576, Height 358
Weight: approximately 9 kg
-
8/3/2019 COPIA 9017_UK
35/38
30 OPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICESOPTIONAL DEVICES
CONTROL CARD / PRINTER UNITCONTROL CARD / PRINTER UNITCONTROL CARD / PRINTER UNITCONTROL CARD / PRINTER UNITCONTROL CARD / PRINTER UNIT (((((inside cover, sect. Finside cover, sect. Finside cover, sect. Finside cover, sect. Finside cover, sect. F)))))
The control card enables you to manage the use of the photocopier more efficiently, by restricting access to
authorized personnel only, and allowing you to check the number of copies made by each card holder and the total
number of copies made.
Using the control card
If the icon blinks when the photocopier is switched on, insert
the control card in the slot in order to use the photocopier (Control card, p. 15).
Printer Unit
By connecting the printer unit to the control card reader, you can
keep a record of photocopier use for administrative purposes, such
as cost per copy, cost per user, billing and inventory.
-
8/3/2019 COPIA 9017_UK
36/38
31
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
INDEXINDEXINDEXINDEXINDEX
INDEXINDEXINDEXINDEXINDEX
AAAAA
Auto clear 7
Auto power -off 7
Automatic document feeder - ADF 19-21
BBBBB
Basic configuration 3
Book copying 9
Bypass See Stack bypass
CCCCC
Cleaning 17
Consumables 18
Control card 5, 15, 30
Control panel 4Copy exposure 7
Copy paper 11, 15, 18
Copying on special media 10
Copying ratio (selection) 8
DDDDD
Display 4, 15
GGGGG
Group mode 22, 24
IIIII
Identification of originals not copied 21
Installation 2
JJJJJ
Jammed staples 28
Jams 13-14, 20, 23, 28, 29
MMMMM
Manual insert stapling 26
NNNNN
Number of copies 7
PPPPP
Paper cassette 11
Paper loading 8, 11
Power supply 3
Precautions 2
Printer Unit 30
RRRRR
Reductions/enlargements (automatic) 9
Reductions/enlargements (preset) 8
Reductions/enlargements (zoom) 9
Reductions/enlargements in automatic mode 9
SSSSS
Sorter 5, 22-23
Sorting modes 22, 24
Stack bypass 6, 8, 10
Standard copy sizes 3
Standard setting 6
Staple cartridge 25, 26, 27
Stapler sorter 5, 24-29
Staples (positioning) 25, 26
Stapling 24, 25
TTTTT
Toner 12, 15
Transparencies 8, 10
Troubleshooting 16
Two sided copying 10
ZZZZZ
Zoom 9
-
8/3/2019 COPIA 9017_UK
37/38
A 1 2 3 4 5 6 7 8 9 10 11 12 13 14
15 16 17 18 19 20 21 22
23
24
25
26 27
28
29
30
B 12 3 4
6
1516
5
7
8
9
10
11
1213
14
17
18
-
8/3/2019 COPIA 9017_UK
38/38
C
D
F
E
2 1
3
5
6
2 1
1
4
1
2 2 3
45