LP7000 Spec

7/30/2019 LP7000 Spec

1/16

LP7000

Specifications

7/30/2019 LP7000 Spec

2/16

7/30/2019 LP7000 Spec

3/16

1

Specifications

System

Printer processor section

Overall dimensions See Dimensions.

Processing speed 1638 mm/minute

Heating capacity About 0.453 kW (about 390 kcal/h)

Weight Approx. 301.73 Kg

Exposure conditions Controlled with the built-in colorimeter.

Operati

on

section

Display module

Exposure engine iBeam Engine

The flatbed scanner recommended by us*1, which is used at iBeam Engine

setup, is necessary.

To know more about the flatbed scanner, please consult your technical

representative.

*1. For the suitable flatbed scanner models, see Flatbed scanner

(recommended) as explained later.

Print resolution

Main scanning:Sub-scanning: 300 dpi300 dpi

Exposure speed 27.94 mm/second

Exposure system Exposure scanning via paper advance

Print size

Paper width: 89, 102, 114, 117, 120, 127, 130, 152, 165, 178, and 203 (mm)

Paper advance length: from 82.5 to 610.0 mm

Paper supply Single magazine type (Dual magazine type and triple magazine type are

factory options.)

Paper specification Maximum diameter of paper roll: 250 mm

Transport system Roller transport system

Temperature control Temperature in each sub-tank is controlled separately.

Replenishment system The system calculates the processed amount of paper surface based on the

print size and automatically supplies the appropriate amount of replenisher

to each tank.

Water refilling Water refilling is performed automatically when the solution level sensors

are activated.

Automatic cleaning The upper guides are automatically cleaned at close down checks.

7/30/2019 LP7000 Spec

4/16

2

External interface

Processing tank capacity Color Developer

8.5 liters

Bleach Fixer

8.2 liters

Stabilizer

11.6 liters

Processing time Color Developer

22.3 sec (31.1 sec)*1

Bleach Fixer

27.1 sec (37.8 sec)*1

Stabilizer

43.1 sec (60.1 sec)*1

Dryer

14.5 sec (20.2 sec)*1

*1. Processing time required for some types of paper

Processing temperature Color Developer

420.3C

Bleach Fixer402.0C

Stabilizer

38 - 42C

Replenishment solution tank capacity Color Developer

6.6 liters

Bleach Fixer

6.0 liters

Stabilizer

17.1 liters

Effluent tank capacity Color Developer

4.0 liters Bleach Fixer

4.1 liters

Stabilizer

5.8 liters

Collection of effluents Two effluents are separately collected by natural dripping.

Dryer Hot air ink drying method

Energy-saving type using automatic power control

Order classification Max. three orders (Varies depending on the paper size.)*1

*1. Maximum 12 orders when print sorter unit type 1 (option) is installed.

Maximum 10 orders when print sorter unit type 2 (option) is installed.

Ethernet (100Base-TX) 1 port

Display module interface 1 port

External AC power outlet Outlet type 3 output

Power supply voltage 200 V to 240 V (conform to the power supply specification)

Power capacity 3A

7/30/2019 LP7000 Spec

5/16

3

Flatbed scanner (recommended products)

Actual tank capacities may differ slightly from the volumes shown above.

Depending on the combination of paper and processing solution, maximum density of print may be different.

For details, contact your place of purchase.

Manufacturer Product name

EPSON A4 flatbed scanner

Perfection 4990 Photo

Perfection V700 Photo

Perfection V750

7/30/2019 LP7000 Spec

6/16

4

Processing capacity

Repeat processing capacity

*1. Calculated according to our criteria. The actual processing capacities may differ depending on various conditions.

Repeat processing capacity

The following is the processing capacity for some types of paper.

*1. Calculated according to our criteria. The actual processing capacities may differ depending on various conditions.

Print size (Paper width Paper advance length) Capacity (Prints/hour)*1

120 mm 82.5 mm 823

127 mm 89 mm 781

152 mm 102 mm 758

203 mm 102 mm 758

89 mm 127 mm 622

102 mm 152 mm 527

127 mm 178 mm 455

102 mm 203 mm 402

203 mm 254 mm 325

203 mm 305 mm 259

203 mm 610 mm 96

Print size (Paper width Paper advance length) Capacity (Prints/hour)*1

120 mm 82.5 mm 688

127 mm 89 mm 647

152 mm 102 mm 578

203 mm 102 mm 578

89 mm 127 mm 480102 mm 152 mm 410

127 mm 178 mm 356

102 mm 203 mm 316

203 mm 254 mm 258

203 mm 305 mm 217

203 mm 610 mm 85

7/30/2019 LP7000 Spec

7/16

5

Required space and dimensions

Space required for installation

! For single magazine type

*1. Extension table (option) not attached

*2. The required space is the same even if the print sorter unit (option) is installed.

*3. If there is additional space in the installation area, we recommend leaving a space of 205 mm or more between the back of system

and wall to facilitate maintenance operations.

! For dual magazine type/triple magazine type

*1. The required space is the same even if the print sorter unit (option) is installed.

*2. If there is additional space in the installation area, we recommend leaving a space of 205 mm or more between the back of system

and wall to facilitate maintenance operations.

1390ormore

*2

90ormore

3

250 or more

2100 or more350 or more*1

(Unit: mm)

Extension table (option)

G088213

Dual magazine unit (option) or triple magazine unit (option)

2390 or more

(Unit: mm)

250 or more

90ormore

*2

182 or more

1390ormore

*1

G088214

7/30/2019 LP7000 Spec

8/16

6

Dimensions

*1. When the print sorter unit (option) is installed

*2. When the processing rack is lifted

*3. When the table is raised to the top

640

526

(Unit: mm)

13

35

1957.8

1499.8

1

3902

Dual magazine unit (option) or triple magazine unit (option)

775(827*1)

70

0

1849.8

9551

155*3

G088215

7/30/2019 LP7000 Spec

9/16

7

Power capacity

The values shown here are for installing the power supply.

Supply voltage should be within 10% of the specified voltage.

The power capacity varies depending on the power supply specification.See the appropriate information for each specification.

The three-phase four-wire system is not used in the United States.

IMPORTANT

Use a grounding resistance of 100 or less when grounding this product.

For details about 1P2W, see1P2W.



"""" 1P2W

Wiring chart

*1. Supply voltage should be within 10% of the specified voltage.

*2. This is the capacity required for power supply installation.

*3. When installing the film processor, be sure to provide a separate circuit breaker from the printer processor.

NOTE

Leakage current value: 11.2 mA (reference value)

"""" 3P3W

Supply voltage*1 Power capacity*2

AC 200 V 3.6 kVA (18 A)

AC 208 V 3.8 kVA (18 A)

AC 220 V 3.7 kVA (17 A)

AC 230 V 3.8 kVA (17 A)

AC 240 V 4.0 kVA (17 A)

Supply voltage*1 Power capacity*2

AC 200 V 3.6 kVA (12 A)

AC 208 V 3.8 kVA (13 A)

AC 220 V 3.7 kVA (11 A)

AC 230 V 3.8 kVA (11 A)

AC 240 V 4.0 kVA (11 A)

*3

*3

(30 A)

Circuit breaker Main circuit breaker

Printer processor

Ground

1P2W

(AC 200 V-240 V)

Power supplyDistribution box

G075757

7/30/2019 LP7000 Spec

10/16

7/30/2019 LP7000 Spec

11/16

9

Standard equipment

Printer section

*1. The paper width can be selected from the following:

89, 102, 114, 117, 120, 127, 130, 152, 165, 178, and 203 (mm)

Paper processor section

Item StatusCastors Attached

Magazine*1 1

Table height adjust function Built-in

Correction value printing unit (CVP) Installed

Display module Installed

Item Status

Remote effluent tank Built-inEffluent level alarm (1 per tank) Built-in

Dryer overheat prevention system Built-in

Solution overheat prevention system Built-in

Processing tank level alarm Built-in

Circulation pump stop alarm Built-in

Dryer temperature setting function (for each paper magazine) Built-in

Drive and dryer automatic stop function Built-in

Castors Attached

Print conveyor unit Installed

Control strip holder 1

Surge absorber (surge protection circuit) Built-in

Automatic cleaning Built-in

Replenishment solution remaining amount alarm (1 per tank) Built-in

Automatic water refilling unit Built-in

Incorrect cartridge loading prevention function Built-in

Automatic solution mixing Built-in

7/30/2019 LP7000 Spec

12/16

10

Standard accessory

Printer processor section

Name Quantity RemarksC-ring #4 5 Accessory for processing rack

C-ring #6 5 Accessory for processing rack

Vinyl hose (inside diam. 9 mm outside diam. 13 mm length

1500 mm)

1 For treating effluent

Slow-blow fuse (3.15 A) 2 Spare item

Slow-blow fuse (6.3 A) 2 Spare item

Slow-blow fuse (10 A) 2 Spare item

Slow-blow fuse (5 A) 2 Spare item

Glass tube fuse (2 A) 2 Spare item

Check date entry sticker 1 Sticker to write the date that float switch

operation was checkedStick 1 For checking the operation of the float

switch in the processing tank

Cleaning sheet 1 Cloth for cleaning the colorimeter unit

Cleaning wiper 1 Cleaning supply

Lower turn belt 1 Accessory for processing rack

Lower turn belt (3) 1 Accessory for processing rack

Washing bottle (500 ml) 1 For cleaning processing rack

Measuring hose (1) 1 For Color Developer replenishment

solution, Bleach Fixer and Stabilizer

replenishment solution

Measuring hose (2) 1 For measuring replenishment solution

(PS1 and PS2)

Measuring hose (3) 1 For measuring replenishment solution

(PS3 and PS4)

Paper holder 1 For measuring test prints for iBeam

tuning

Plug code (1 m) 1 Power supply cable for PC

Plug code (2.5 m) 1 Power supply cable for monitor

LAN cable (0.7 m) 1 Cross type

Flat cable clamp 5

Anti-contamination cover (includes the maintenance cover) one each Prevents auxiliary solutions from

dripping into the CD solution when

removing processing racks, etc. (Themaintenance cover is for preventing

processing solution from adhering to the

processor loading unit.)

Chain Oil 1 Oil for lubricating the dryer drive chain

7/30/2019 LP7000 Spec

13/16

11

Options (Printer)

Some of the following options may not be available in some countries and areas.


Printer section

Paper magazine

Option No. Name Explanation

Z804937-01 DP bag hanger (DH-6) Hanger for holding developed films and DP bags.

H086044-00 Ink ribbon cassette CVP ink ribbon

Z811139-01 Dual magazine unit Unit compatible with the dual magazine type

The paper magazine is required separately.

(available as factory option)

Z811140-01 Triple magazine unit Unit compatible with the triple magazine type

The paper magazine is required separately.

(available as factory option)

Z811135-01 Expansion table Mainly used to place the A4 flatbed scanner on.

Z810651-01 Counter unit Indicates the number of prints.

Z811137-01 Monitor table Table to place the display monitor on

Z811114-01 LCD monitor arm Monitor arm with which you can freely change direction

of the display.

Z811147-01 Rear cover The cover to hide the rear side of the machine.

Z811191-01 Storage cabinet When the table is raised, a cabinet can be installed under

the table.

I068490-00 Plug cord For connecting the scanner (1.5 m)


Z811196-02 Paper magazine, 89 mm Include Magazine spindle unit 1 and handle.

Z811196-03 Paper magazine, 102 mm










7/30/2019 LP7000 Spec

14/16

12

Options (Paper processor)

Some of the following options may not be available in some countries and areas.


Paper processor section


C008075-01 Floor tray Placed underneath the system to prevent the floor from

becoming dirty.

B011625-01 Rack transportation tank Used to transport wet processing racks.

C101570-01 Turn rack vat Container for immersing the upper guide in water.

A202513-01 Filler 5-liter measuring pitcher

H049014-00 Effluent tank Collects effluent that overflows from the processing

tanks. (20 liters)

L005253-00 Measuring cylinder Used to measure replenishment solution, etc. (200 ml).

Z810657-01 Minute meter unit Displays the system operating time.Z811175-01 Sorter modification kit (10 orders) Modifies the print sorter unit to support 10 orders (only

when print sorter unit type 1 is installed)

H089016-00 Cleaning sheet Used to clean the pressure roller of the colorimeter unit.It

should be cleaned every six months. Three sheets

included.

Z811171-01 Print sorter unit (type 1) Allows prints to be sorted by order (12-order type).

Z811172-01 Print sorter unit (type 2) Allows prints to be sorted by order (10-order type).

Z811150-01 Control strip auto loading unit Unit to process the control strip without using the control

strip leader.

7/30/2019 LP7000 Spec

15/16

13

Commercially available items to be

prepared by the customer

The items below are required according to the installation environment of the customers.

They should be prepared by customers if necessary.

Item Remarks

HUB When several systems are connected to the PC, a hub is

necessary. (Should be with the required number of 100BASE-TX

ports.)

LAN cable Cross type The cable of 0.7 m is supplied as a standard accessory. If the

longer cable is required, prepare the longer cable.

Straight type Prepare this when connecting the system using a HUB.

7/30/2019 LP7000 Spec

16/16

14

Installation requirements

This system is to be used in a location with a relative humidity from 30 to 75% and temperature from 15 to 30C (59 to

86F).

The light source for this system should be a natural light color, and the light intensity should be between 300 and 400 lux.

If there are lights near to the system, they must be screened. In particular, if the product is installed near a window, use

curtains or blinds to block direct sunlight from the product.

Do not install the product in a place where the operator is exposed to direct sunlight. Make sure the display monitor is

located away from direct sunlight or other bright light sources.

Avoid installing the product in areas with high dust levels or subject to vibration.

Do not raise or lower the room temperature quickly. Raising the temperature quickly can cause condensation inside the

system, which leads to problems such as lens fogging, paper jam, and malfunctions in the electronics and PCBs.

Because the system uses liquids during normal operation, please make sure that the floor and walls are waterproof for

safety reasons. In addition, we recommend installing a sink or drain in the room to facilitate washing racks.

Castors are for moving the system. Once the system has been installed, be sure to fix it in place with the adjusters or jack

bolts.

If the level difference of the floor on which the system is installed (the height difference between jack bolts) is 10 mm or

more, a plate or shim should be used to adjust the level.

Use this system in a DC magnetic field (earth magnetic field, etc.) of 0.6G*1or less and AC magnetic field (power source

magnetic field, etc.) of 0.06G*1 (rms) or less.

*1. 0.6G = 60T, 0.06G = 6T

The system is programmed with default values prior to shipment. These values may differ depending on the environment

and operating conditions. Change them as necessary.

The maximum permissible system impedance Zmax of this system is 0.063+j0.039, supplied from a power distribution

system having a rated voltage of 400/230 V. This system is connected only to a supply of that impedance or less.

Determine the connection to a power supply in consultation with the supply power company.

This equipment complies with EN61000-3-12.

Subject to change without notice.

LP7000 Spec

Documents

Transcript of LP7000 Spec