Daewoo 1 en

7/27/2019 Daewoo 1 en

1/9

EMULATOR IMMODAEWOO 1

technical support:www.carlabimmo.com/forumang/
http://www.carlabimmo.com/forumang/http://www.carlabimmo.com/forumang/http://www.carlabimmo.com/forumang/

7/27/2019 Daewoo 1 en

2/9

Jumper settings on board of Universal Car Emulator Julie:

Solder jumper J1, J2 and J3 on the emulator


7/27/2019 Daewoo 1 en

3/9

With white - red plug

With blue plugs

Thank you for purchasing our device.Emulator immo to Daewoo cars replaces damaged immobilizer or the car key. It is

necessary to made changes in memory content of Engine Control Module.In case of losing the car keys or a car burglary it enable to drive off from the road

to the car service.Due to a low cost, you can leave it in the car instead of buying a new immo or

making car keys duplicate.There is a possibility of using it as the additional security!!!

Two LEDs indicating:green power

red- after adjusting it lights constantly

In selected models of ECU you can programmaticallydisable immo without necessity to use the emulator.

http://www.carlabimmo.com/forumang/http://www.carlabimmo.com/forumang/https://carlabimmo.com/attachment.php?id_attachment=91https://carlabimmo.com/category.php?id_category=6http://www.carlabimmo.com/forumang/

7/27/2019 Daewoo 1 en

4/9

ECU with white - red plug

In the engine driver find a Motorola processor HC11F1 to use emulator in line FE10type twice 73 00 73 00.


7/27/2019 Daewoo 1 en

5/9

After processing Motorola, connect emulator to the driver as pictured.

Before connecting the driver, emulator must be precisely isolated by the isolationstrap.

Before connecting the emulator there is a necessity to take off the originalimmobilizer!!!

In case when delay needed to start the car again is more than 10seconds to thenchange constant suplly (+12V) on power after the ignition (+12V ACC).


7/27/2019 Daewoo 1 en

6/9

ECU with blue plugs

In the engine driver find a Motorola processor HC11F1To use emulator in line FE10 type twice 73 00 73 00


7/27/2019 Daewoo 1 en

7/9

After processing Motorola, connect emulator to the driver as pictured.

ground ground of resonator (quartz)

code 1 leg of unit DELCO 9621

power 11 leg of unit DELCO 9621

Unhook immo or cut off pin B7 from the Engine Control Module.

Before connecting the driver, emulator must be precisely isolatedby the isolation strap.

Before connecting the emulator there is a necessity to take off theoriginal immobilizer!!!


7/27/2019 Daewoo 1 en

8/9

In case when delay needed to start the car again is more than 10seconds, then cut off constant suplly (+12V) pin and in place of it

serve power from second position of the ignition (+12V ACC).

Warning!!!

Due to possible construction changes of the cars, before connectingthe device

check signals by multimeter on the ECU plug.


7/27/2019 Daewoo 1 en

9/9

We state, that we are the only authentic authors of this manual. We

possess copyright to this publication. All rights reserved.

Unauthorized copying, hiring, lending, public performance will be

punished!!! Any trials of unauthorized copying, hiring, quoting

prohibited!!! Both service and advertisement constitute copyright and

they are the subject to the protection in accordance with the Act from

4th Feb. 1994 on Copyright and Related Laws (Statute Book no. 24

position 93) and protection on the basis of the Act from 8th June 1993

on combating an unfair competition (Statute Book no. 47 position

211).

www.carlabimmo.com

Last update of instructions: 24.01.2013

http://www.carlabimmo.com/http://www.carlabimmo.com/forumang/http://www.carlabimmo.com/forumang/http://www.carlabimmo.com/http://www.carlabimmo.com/forumang/

Daewoo 1 en

Documents

Transcript of Daewoo 1 en